Get flat 7% off on every purchase for minimum spent of 10000/-
Get flat 5% off on every purchase for minimum spent of 7500/-
Get flat 3% off on every purchase for minimum spent of 5000/-
Get Flat Rs 100/- off as welcome bonus on minimum purchase of Rs 2000/-
3m Espe Filtek Bulk Fill Flowable Restorative – Refills
The 3M™ Filtek™ Bulk Fill Flowable Restorative is engineered for efficient dental restorations with enhanced strength, wear resistance, and radiopacity. It features a specialized formulation of fillers and monomers that minimizes shrinkage and polymerization stress, crucial for maintaining restoration integrity. Its low viscosity allows for easy adaptation in deep cavities, requiring minimal instrumentation for placement. Capable of curing up to 4mm in depth, it supports bulk fill procedures, optimizing workflow efficiency. The material can be safely warmed for up to one hour at 70°C, facilitating injection molding and ensuring precise application. Whether used as a base or a liner, this flowable composite resin offers dental professionals a versatile solution that combines ease of use with reliable performance, contributing to durable and aesthetically pleasing restorations.Indications:Base under Class I and II direct restorations
Liner under direct restorative materials
Pit and fissure sealant
Restoration of minimally invasive cavity preparations (including small, non-stress-bearing occlusal restorations)
Class III and V restorations
Undercut blockout
Repair of small enamel defects
Repair of small defects in esthetic indirect restorations
Repair of resin and acrylic temporary materials
As a core build-up where at least half the coronal tooth structure is remaining to provide structural support for the crown.
Optimized Filler and Monomer Blend: Designed to maximize strength, wear resistance, and radiopacity while minimizing shrinkage.
Low Viscosity: Ensures easy adaptation in deep restorations with little or no instrumentation.
Low Shrinkage and Polymerization Stress: Intelligent selection of monomers and fillers produces a restorative with minimal shrinkage and stress during polymerization.
Bulk Fill Capability: Can be used to perform bulk fill restorations with a depth of cure up to 4mm.
Warming Tolerance: Capsules can be safely warmed up to 70°C for up to one hour, allowing for injection molding.
Versatile Applications: Suitable for use as a bulk fill base or a low-stress liner in various restorative procedures.
Radiopaque: Easily distinguishable on radiographs, aiding in diagnosis and follow-up.
Excellent Handling Properties: Flowable consistency allows for precise placement and easy adaptation to cavity walls.
Strong Bond: Provides durable adhesion when used with compatible bonding agents.
Aesthetic Results: Offers good color stability and matches the natural tooth shade for pleasing aesthetic outcomes.
Composite Type: Bulk Fill Flowable
Cure Type: Light Cure
Delivery System: Capsule, Syringe
Depth of Cure: 4mm
Material Structure: Microhybrid Composite
Shades: A2, A3
How to Use 3M™ Filtek™ Bulk Fill Flowable Restorative Capsules
Preparation:Ensure the tooth is clean and dry. Use a rubber dam if necessary to isolate the area.
Apply retraction paste and clean the tooth surface thoroughly.
Etching:Apply a phosphoric acid etchant to the prepared cavity for 15-30 seconds.
Rinse thoroughly with water and dry the tooth without desiccating it.
Bonding:
Apply a bonding agent according to the instructions.
Light-cure the bonding agent for the recommended time.
Warming (Optional):
Warm the capsules up to 70°C for up to one hour if desired.
Dispensing:
Attach the capsule to a dispensing gun.
Application:
Dispense the flowable restorative material directly into the cavity.
Use a dental instrument to ensure even distribution and fill the entire cavity space.
Layering:
For deep cavities, apply the material in increments up to 4mm in depth.
Ensure each layer is adequately cured before applying the next layer.
Curing:
Use a curing light to polymerize the material. Follow the recommended curing time.
Ensure the light covers the entire restoration area for uniform curing.
Finishing:
Once the final layer is cured, proceed with finishing and polishing the restoration.
Final Check:
Verify the occlusion and make any necessary adjustments.
Ensure the restoration is smooth and comfortable for the patient.
How to Use 3M™ Filtek™ Bulk Fill Flowable Restorative Syringe
Preparation:
Ensure the tooth is clean and dry. Use a rubber dam if necessary to isolate the area.
Apply retraction paste and clean the tooth surface thoroughly.
Etching:
Apply a phosphoric acid etchant to the prepared cavity for 15-30 seconds.
Rinse thoroughly with water and dry the tooth without desiccating it.
Bonding:
Apply a bonding agent according to the instructions.
Light-cure the bonding agent for the recommended time.
Warming (Optional):
Warm the syringe up to 70°C for up to one hour if desired.
Dispensing:
Remove the cap and attach a suitable dispensing tip to the syringe.
Application:
Slowly dispense the flowable restorative material directly into the cavity.
Use a dental instrument to ensure even distribution and fill the entire cavity space.
Layering:
For deep cavities, apply the material in increments up to 4mm in depth.
Ensure each layer is adequately cured before applying the next layer.
Curing:
Use a curing light to polymerize the material. Follow the recommended curing time.
Ensure the light covers the entire restoration area for uniform curing.
Finishing:
Once the final layer is cured, proceed with finishing and polishing the restoration.
Final Check:
Verify the occlusion and make any necessary adjustments.
Ensure the restoration is smooth and comfortable for the patient.
3M™ Filtek™ Bulk Fill Flowable Restorative is a dental composite material used for filling cavities. It allows for bulk filling of cavities up to 4mm in depth in a single increment, simplifying and speeding up the restorative process.
The depth of cure is up to 4mm.
The low viscosity allows for easy adaptation in deep restorations with minimal or no instrumentation.
Capsules can be safely warmed up to 70°C for up to one hour and then injection molded.
Yes, it is designed to be radiopaque.
Reviews
There are no reviews yet.
Only logged in customers who have purchased this product may leave a review.